SeaDoo XP DI Instructions d'exploitation

8FUNCTIONS OF CONTROLS, COMPONENTS AND INSTRUMENTSThe following components have thesame operation as explained in the2003 Operator’s Guide, only their

926) Mooring CleatsAll Models These cleats can be temporarily used fordocking, while refueling for example.CAUTION: Never use mooring cleatsto pull or

10OPERATING INSTRUCTIONSVariable Trim SystemThe variable trim system (VTS) chang-es the angle of the jet pump nozzle toprovide the operator with a fas

11TYPICAL1. Push on arrow pointing downward on VTSbutton2. Bow down3. Nozzle downF08J0BY2138°smo2003-004b.fm Page 11 Wednesday, January 22, 2003 11

12SPECIAL PROCEDURESTowi ng the Watercraft in WaterIt is the same as explained in the 2003Operator’s Guide. The hose locationand routing differs. Refe

13MAINTENANCELubricationSeal CarrierUsing a grease gun, carefully lubricateseal carrier of mid bearing until greaseis just coming out of seal.1. Greas

14FusesRefer to this updated text and illustra-tions.Fuses can be found at 2 locations; onthe MPEM and in the electrical box.MPEMTo access fuses on th

151. Electrical boxUnclip and remove cover of the electri-cal box to expose the holder of themain fuse.TYPICAL1. Fuse holderElectric bilge pump fuse i

16TRAILERING, STORAGEAND PRE-SEASON PREPARATIONThe information pertaining to traile-ring, storage and pre-season prepara-tion is similar to the one

17CAUTION: Antifreeze mix must befed in cooling system. Otherwise re-maining water will freeze. This opera-tion requires a good technical knowl-edge o

SAFETY WARNINGDisregarding any of the safety precautions and instructions contained in thisOperator’s Guide, the Safety Handbook, the Safety Videocass

18Hose DisconnectionDisconnect the bottom hose at the wa-ter regulator valve on muffler.1. Disconnect the bottom hose from water regulator valve Tempo

191. Engine drain hose (crankcase cooling outlet)Continue to pour until antifreeze flowsin air compressor water outlet hose.1. Air compressor water ou

20Clean the bilge with hot water and de-tergent or with bilge cleaner. Rinsethoroughly. Lift front end of watercraftto completely drain bilge. If any

21SPECIFICATIONSENGINEXP DI(6130/6131)Engine type Rotax 947, 2-strokeInduction type Reed valveExhaust system Water cooled/water injected with regulato

22➀ Refer to load limit.BOMBARDIER INC. reserves the right to make changes in design and specifica-tions and/or to make additions to, or improvements

1NOTEDear 2003 XP DI watercraft owner. Use the information pertaining to the RXDI model in the 2003 Operator’s Guide (P/N 219 000 290) and then use th

2TABLE OF CONTENTSLOCATION OF THE IMPORTANT LABELS ... 3LOCATION OF CONTROLS, COMPONENTS AND INSTRUMENTS . 6FUNCTIONS

3LOCATION OF THE IMPORTANT LABELS XP DI ModelsTYPICALF08L1UL8429123-5smo2003-004b.fm Page 3 Wednesday, January 22, 2003 11:41 AM

4Label 1F08A04Lsmo2003-004b.fm Page 4 Wednesday, January 22, 2003 11:41 AM

5XP DI Model OnlyThe location of these labels differ onthe XP DI model.Label 2Label 3Label 4Label 5Label 8Label 9Label 12F00A22YF02L2D0F00L29YF00L2XYF

6LOCATION OF CONTROLS, COMPONENTS AND INSTRUMENTSXP DI ModelTYPICALNOTE: Components not shown here are the same as on the RX DI models inthe 2003 Sea-

714) Fuel Tank Cap15) Oil Injection Reservoir Cap16) Front Storage Compartment Cover18) Tool Kit19) Air Intake Opening23) Rear Grab Handle26) Mooring